% Load plain if necessary, i.e., if running under initex.
\expandafter\ifx\csname fmtname\endcsname\relax\input plain\fi
%
-\def\texinfoversion{2013-01-01.15}
+\def\texinfoversion{2013-08-09.09}
%
% Copyright 1985, 1986, 1988, 1990, 1991, 1992, 1993, 1994, 1995,
% 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006,
\ifx\next,%
\else\ifx\next-%
\else\ifx\next.%
+ \else\ifx\next\.%
+ \else\ifx\next\comma%
\else\ptexslash
- \fi\fi\fi
+ \fi\fi\fi\fi\fi
\aftersmartic
}
}
% We *must* turn on hyphenation at `-' and `_' in @code.
+% (But see \codedashfinish below.)
% Otherwise, it is too hard to avoid overfull hboxes
% in the Emacs manual, the Library manual, etc.
%
% Unfortunately, TeX uses one parameter (\hyphenchar) to control
% both hyphenation at - and hyphenation within words.
% We must therefore turn them both off (\tclose does that)
-% and arrange explicitly to hyphenate at a dash.
-% -- rms.
+% and arrange explicitly to hyphenate at a dash. -- rms.
{
\catcode`\-=\active \catcode`\_=\active
\catcode`\'=\active \catcode`\`=\active
\let-\codedash
\let_\codeunder
\else
- \let-\realdash
+ \let-\normaldash
\let_\realunder
\fi
+ % Given -foo (with a single dash), we do not want to allow a break
+ % after the hyphen.
+ \global\let\codedashprev=\codedash
+ %
\codex
}
+ %
+ \gdef\codedash{\futurelet\next\codedashfinish}
+ \gdef\codedashfinish{%
+ \normaldash % always output the dash character itself.
+ %
+ % Now, output a discretionary to allow a line break, unless
+ % (a) the next character is a -, or
+ % (b) the preceding character is a -.
+ % E.g., given --posix, we do not want to allow a break after either -.
+ % Given --foo-bar, we do want to allow a break between the - and the b.
+ \ifx\next\codedash \else
+ \ifx\codedashprev\codedash
+ \else \discretionary{}{}{}\fi
+ \fi
+ % we need the space after the = for the case when \next itself is a
+ % space token; it would get swallowed otherwise. As in @code{- a}.
+ \global\let\codedashprev= \next
+ }
}
-
+\def\normaldash{-}
+%
\def\codex #1{\tclose{#1}\endgroup}
-\def\realdash{-}
-\def\codedash{-\discretionary{}{}{}}
\def\codeunder{%
% this is all so @math{@code{var_name}+1} can work. In math mode, _
% is "active" (mathcode"8000) and \normalunderscore (or \char95, etc.)
}
% An additional complication: the above will allow breaks after, e.g.,
-% each of the four underscores in __typeof__. This is undesirable in
-% some manuals, especially if they don't have long identifiers in
-% general. @allowcodebreaks provides a way to control this.
+% each of the four underscores in __typeof__. This is bad.
+% @allowcodebreaks provides a document-level way to turn breaking at -
+% and _ on and off.
%
\newif\ifallowcodebreaks \allowcodebreakstrue
% ..., but we might end up with active ones in the argument if
% we're called from @code, as @code{@value{foo-bar_}}, though.
% So \let them to their normal equivalents.
- \let-\realdash \let_\normalunderscore
+ \let-\normaldash \let_\normalunderscore
}
}
% @ifset VAR ... @end ifset reads the `...' iff VAR has been defined
% with @set.
-%
-% To get special treatment of `@end ifset,' call \makeond and the redefine.
+%
+% To get the special treatment we need for `@end ifset,' we call
+% \makecond and then redefine.
%
\makecond{ifset}
\def\ifset{\parsearg{\doifset{\let\next=\ifsetfail}}}
\newdimen\nonfillparindent
\def\nonfillstart{%
\aboveenvbreak
- \hfuzz = 12pt % Don't be fussy
+ \ifdim\hfuzz < 12pt \hfuzz = 12pt \fi % Don't be fussy
\sepspaces % Make spaces be word-separators rather than space tokens.
\let\par = \lisppar % don't ignore blank lines
\obeylines % each line of input is a line of output
@gdef@otherbackslash{@let\=@realbackslash}
% Same as @turnoffactive except outputs \ as {\tt\char`\\} instead of
-% the literal character `\'.
-%
-@def@normalturnoffactive{%
- @let"=@normaldoublequote
- @let$=@normaldollar %$ font-lock fix
- @let+=@normalplus
- @let<=@normalless
- @let>=@normalgreater
- @let\=@normalbackslash
- @let^=@normalcaret
- @let_=@normalunderscore
- @let|=@normalverticalbar
- @let~=@normaltilde
- @markupsetuplqdefault
- @markupsetuprqdefault
- @unsepspaces
+% the literal character `\'. Also revert - to its normal character, in
+% case the active - from code has slipped in.
+%
+{@catcode`- = @active
+ @gdef@normalturnoffactive{%
+ @let-=@normaldash
+ @let"=@normaldoublequote
+ @let$=@normaldollar %$ font-lock fix
+ @let+=@normalplus
+ @let<=@normalless
+ @let>=@normalgreater
+ @let\=@normalbackslash
+ @let^=@normalcaret
+ @let_=@normalunderscore
+ @let|=@normalverticalbar
+ @let~=@normaltilde
+ @markupsetuplqdefault
+ @markupsetuprqdefault
+ @unsepspaces
+ }
}
% Make _ and + \other characters, temporarily.